Medium

Available on

Apple Android Windows

Cryogenic Transfer Vessels: Operation Mobile App

WARNING Liquid nitrogen is extremely cold; it boils at -196°C. Extreme caution should be exercised when handling cryogenic liquids. Always wear proper safety attire when transferring liquid nitrogen into or out of Thermo cylinders. Contact with a cryogenic liquid or cold gas may cause frostbite to unprotected areas of the body. Protect eyes and skin when transferring liquid. Stand clear of vent during filling. Loose fitting, insulated gloves and long sleeves are recommended for arm protection. Cuffless pants should be worn outside boots or overshoes to shed spilling liquid. Goggles or face shields should be worn if the possibility of splashing liquid exists. Failure to observe this warning may lead to severe burns or eye injuries. To avoid damage to your Thermo cryogenic vessel which may result in premature vacuum loss, it is important that Cryogenic Transfer Vessels: Operation mobile app be used during the addition of liquid nitrogen to a warm vessel and on subsequent additions. If you have an iPhone, iTouch or iPad you need to first download GoCanvas from the onboard App Store on your device.

  • Lendlease
  • The Cooperative
  • PG&E
  • Red Bull
  • Mirvac

Want to learn more about GoCanvas?

Request a Demo

Take a peek inside the Cryogenic Transfer Vessels: Operation Mobile App

Included Features

Our App Builder gives you the power to easily add and remove the ones you want. {{controller.show_all ? 'See included features.' : 'See more features.'}}

  • {{data.title}}

Included Fields

Customize to add, remove, or edit any of the fields below.

  • Ico statictext

    Warning Liquid nitrogen is extremely cold; it boils at -196°C.

  • Ico statictext

    Caution Never overfill your Thermo dewar with liquid nitrogen.

  • Ico statictext

    To avoid damage to your Thermo cryogenic vessel (Thermo® 5, 10, 20 and 30), which may result in p...

  • Ico checkbox

    Add only a small amount of liquid nitrogen (5-10 liters) to new or warm vessels.

  • Ico checkbox

    Allow this small amount of liquid nitrogen to sit in the covered vessel for a minimum of 2 hours.

  • Ico checkbox

    Fill your vessel to the desired level.

  • Ico checkbox

    If you are filling your Thermo dewar from a pressurized source, make sure that the source tank i...

  • Ico checkbox

    If the transfer hose is used for extracting liquid nitrogen from a pressurized liquid source, al...

  • Ico checkbox

    Remember to always wear proper safety attire over clothing, including: face shield, cryogenic gl...

  • Ico checkbox

    To avoid damage to your Thermo cryogenic vessel (Thermo® 5, 10, 20 and 30), which may result in p...

  • Ico checkbox

    Add only a small amount of liquid nitrogen (5-10 liters) to new or warm vessels.

  • Ico checkbox

    Allow this small amount of liquid nitrogen to sit in the covered vessel for a minimum of 2 hours.

  • Ico checkbox

    Fill your vessel to the desired level.

  • Ico checkbox

    If you are filling your Thermo dewar from a pressurized source, make sure that the source tank i...

  • Ico checkbox

    If the transfer hose is used for extracting liquid nitrogen from a pressurized liquid source, al...

  • Ico checkbox

    Remember to always wear proper safety attire over clothing, including: face shield, cryogenic gl...

  • Ico statictext

    The liquid discharge device provides liquid nitrogen for filling cold traps and smaller dewars wi...

  • Ico checkbox

    Rubber Stopper: Provides a seal against the walls of the necktube.

  • Ico checkbox

    Tightening the wingnut expands the rubber stopper.

  • Ico checkbox

    Pressure Gauge: Indicates the pressure inside the container.

  • Ico checkbox

    Relief Valve: Relieves pressure inside the container automatically when excessive pressure is rea...

  • Ico checkbox

    The relief valve is a safety device and cannot be adjusted.

  • Ico checkbox

    Vent Valve: Provides means to vent product.

  • Ico checkbox

    Discharge Valve: Allows product to flow out of the vessel through the discharge device spout.

  • Ico checkbox

    Safety Cable: Prevents discharge device from accidently exiting completely from vessel.

  • Ico statictext

    Perform the following steps to install the liquid discharge device on a vessel:

  • Ico checkbox

    Attach the discharge device spout to the liquid discharge device.

  • Ico checkbox

    Verify that the rubber stopper is dry and free from grease and other contaminants.

  • ...and More!

Related Government & NGO Apps... and they're all free for GoCanvas subscribers!

App Name

OSHA Power and Hand Tools: Electric ...

Employees using electric tools must be aware of several dangers. Among the most serious hazards are electrical burns and s...

App Name

OSHA Power and Hand Tools: Operating...

Hand-held power tools must be equipped with a constant-pressure switch or control that shuts off the power when pressure i...

App Name

Panel Routers Safety Checklist

The Panel Routers Safety Checklist has been turned into a mobile application, and is intended to reduce panel router relat...

App Name

Portable Hand and Power Tools Self In...

The Portable Hand and Power Tools Self Inspection Checklist mobile app covers the regulations issued by the U.S. Departmen...

App Name

Power Tool Safety Program: Drills, H...

All power tools can be dangerous if both general and tool specific safety instructions are not followed carefully. General...

App Name

Power Tool Safety Program: Electric C...

All power tools can be dangerous if both general and tool specific safety instructions are not followed carefully. General...

App Name

Power Tool Safety Program: Metal Cutt...

All power tools can be dangerous if both general and tool specific safety instructions are not followed carefully. General...

App Name

Power Tool Safety Program: Sanders (S...

All power tools can be dangerous if both general and tool specific safety instructions are not followed carefully. General...

More Information


Related Blog Posts